Solar Panel Bird Control Fastener J Hook Aluminium Steel Clips

£6.66£39.16 Including VAT

  • An innovative system designed specifically to keep birds out from under solar arrays protecting the roof, wiring and equipment from damage.
  • Solar clips are recommended every 450mm (18 inches) 2 clips on short edge 3 clips on long edge.
  • Solar clips bind the mesh to the panels without drilling holes or damaging the system
  • A new product that is fast easy & highly effective, making solar panel bird exclusion straight forward
  • This non-penetrating system is fast and easy to install and can be removed for service.
  • A typical solar panel is approximately 1.6m tall and 1m wide, on a typical panel one should use 3 clips on each long edge and 2 clips on each short edge.
SKU: N/A Category:

Description

Solar panel wire mesh bird control fastener J hooks clips are an essential component of any solar panel system that is designed to keep birds and pests away from the panels. These Solar panel wire mesh bird control fastener J hooks clips are made of durable aluminium and are shaped like a “J” to easily hook onto the edges of the solar panels. Solar panel wire mesh bird control fastener J hooks clips are used to secure bird netting or mesh to the panels, helping to prevent birds and pests from nesting or perching on the panels and causing damage.

In addition to protecting the solar panels from bird damage, these clips are also important for safety reasons. They help to prevent birds from getting trapped inside the solar panel system, which can be a hazard.

If you are in need of high-quality solar panel wire mesh bird control fastener J hooks clips, there are many options available on the market. Be sure to choose a reputable supplier to ensure that you are getting the best quality products for your solar panel system and roof protection. With the right bird control fastener J hooks clips in place, you can protect your solar panels and keep your energy production running smoothly.

Solar panel wire mesh bird control fastener J hooks clips are typically made of aluminium and are designed to be durable and resistant to rust and corrosion. Solar panel wire mesh bird control fastener J hooks clips are shaped like a “J” and are used to hold the bird netting in place by hooking over the edges of the solar panels.

 

Installation: Solar panel wire mesh bird control fastener J hooks clips bound to solar panels

This non-penetrating system is fast and easy to install and can be removed for servicing, please see installation images bellow.

STEP 1: Place Solar Panel Bird Control Fastener J Hook clips every 18 inches. Slide the Solar Panel Bird Control Fastener J Hook clip onto the edge of the panel support bracket. Slide as far outward as possible so the clip is all the way on the lip of the panel.

STEP 2: Set the wire mesh screen in place. Make sure the fastener rod comes through the screen at an upward angle as to keep downward pressure on the screen

STEP 3: Slide the speed washer onto the shaft of the Solar Panel Bird Control Fastener J Hook clips assembly until snug. Adjust the screen, as necessary. Tighten speed washer and install the locking nut hand tight, tension can be set to the correct setting with the threaded nut.

STEP 4: Cut off any excess mesh screen sticking over the top edge of the solar panel array. Cut of the Solar Panel Bird Control Fastener J Hook clip assembly rod flush with the exterior of the speed washer.

Use metal shears

Solar Panel Clips and Mesh Kit Installation Guide

  • Place provided Solar Panel Bird Control Fastener J Hook clips with every 30-40cm along the underneath of the solar panel frame and pull tight.
  • Roll out the solar panel wire mesh and cut into manageable 2 meter lengths for easier handling. Position the wire mesh in place, making sure the fastening rod points upwards so it keeps a downward pressure on the wire mesh to create a firm barrier to the roof. Allow the bottom to flare out and curve along the roof, this will ensure rodents and birds cannot access under the wire mesh.
  • Attach the fastening washer and push firmly to the end to tightly secure the mesh.
  • When joining the next section of wire mesh, overlay approximately 10cm and join the 2 pieces with cable ties to create a complete barrier.
  • For outer corners; cut upwards from the bottom until the bend point.
  • For inner corners: cut the wire mesh upwards from the bottom until the bend point, secure any overlay sections together using cable ties.

Manufacturer Recommended Quantity Required:

The manufacturers recommendation every 450mm (18 inches) 2 clips on short edge 3 clips on long edge.

Safety

Take the appropriate safety precautions when working on a roof and on live electrical installations.

Additional information

Weight N/A
Pack of

20, 30, 40, 50, 60, 80, 100

Reviews

There are no reviews yet.

Be the first to review “Solar Panel Bird Control Fastener J Hook Aluminium Steel Clips”

Your email address will not be published. Required fields are marked *

Go to Top